SOBA sticks it to The Man

I've been a member of the Society Of Beer Advocates (SOBA) for almost 2 years, and recently we've got into our first serious bit of campaigning. We became aware that DB Breweries, one of the Big Two breweries in New Zealand, had taken action against the Green Man craft brewery in Dunedin. Green Man's crime? Releasing a low-strength beer called Radler. DB sent a threatening letter pointing out that it owned the trademark for Radler and, after a short battle, Green Man acquiesced. They're only a small company and so couldn't afford to take on the big boys.

The issue is that Radler is a generic beer style. It's not very well known in New Zealand but is fairly common in Germany. A single brewery owning the trademark for a beer style is obviously nonsense. Just imagine if someone trademarked Pilsner, for example. To make matters worse, it turns out that DB have also trademarked Saison in New Zealand.

SOBA decided that this could not be allowed to happen, but it wasn't clear what we could do. A boycott of DB products was proposed, and SOBA is still encouraging people to avoid DB products (which shouldn't be all that painful as there are many many better beers available from craft breweries around New Zealand). SOBA secretary Greig McGill got some excellent publicity for the cause via an article in the Waikato Times, followed by a radio appearance on Radio Live and finally a TV appearance on 3 News·

This publicity led to well-known intellectual property (IP) lawyers James & Wells getting in touch with SOBA and offering to fight for the revocation of the Radler trademark on a pro bono basis. The campaign is now in full swing, via a press release and an excellent interview on TV3's Campbell Live show. We're confident we can win but all support is welcomed. We've had support from around the world, including a UK brewer who used to work for DB but is now supporting our cause.

This is not about beer geeks getting sniffy about a name. This is about allowing creativity and innovation to flourish amongst the community of small brewers. We don't mind if DB continues to brew and market their (technically out of style and pretty unpleasant) Monteiths Radler. Just give up the trademark and let Green Man and others show how it should be done.

The great handpump adventure!

As an Englishman and fan of English real ale, I've always wanted my own handpump/beer engine (the terms are fairly interchangeable). And now, thanks to my Dad, I have one! Dad found someone who could lay his hands on one and shipped it over to me. The shipping cost more than the pump itself, but it was well worth it.

The pump arrived mid-week, but I didn't really get chance to play with it until today. Here's a photo of all the bits laid out on my dining table:

It's in superb condition, factory-reconditioned by the famous Angram company. I then set about figuring out how to connect it to my corny kegs. Which was where I encountered my first problem - the shank for the hose on the bottom of the cylinder (the silver bit in the middle in the photo below) is for half-inch hose, while my standard beer line is 6mm. I was momentarily confused by the 2 connectors with green hoses on the right of the picture, until I figured out that they were the connections for the optional water-cooling system.

However, I've bodged up a solution using a couple of jubilee clips. the narrower bore beer line from my kegs goes inside the wider bore line for about an inch, and 2 jubilee clips secure it. I suspected I may get a leak here, but I was pleasantly surprised.

I then went outside and mounted the handpump on my bar. Boy, does it look good!

Then it was time to hook things up. I part-filled a keg with plain water as a test, then attached my beer line to a standard quick-disconnect fitting. I hooked that up to the keg and locked the pressure relief valve open so air could get into the keg to replace the water being drawn out. A few brisk pulls on the handle and water began coming out of the pump!

Unfortunately not all of the water was emerging from the spout as expected. Some water was dripping from underneath the pump, so it was obvious I had a leak somewhere. Time to strip the cover off and check it down. A little investigation showed that, surprisingly, the leak was not at either of the places I had expected (the join in the beer line or the attachment of the line onto the pump) but from the John Guest fitting which linked the output of the pump onto the dispense spout (see below).

Not sure how I'll fix this. It should be possible to pick up another John Guest fitting and replace it. I suspect it's just a bit old.

So, not quite got beer pouring from the pump just yet, but not far away!